From Ubiquiti Wiki

RouterStation Pro Board Specs

Download RouterStation Pro Dimensions
Download RouterStation Pro STP

1. Overall system configuration

• CPU Atheros AR7161 MIPS 24K running @ 680MHz
  
• MEMORY DDR 128MB
  
• FLASH SPI 16MB
  
• 4-Port Gigabit Ethernet Switch
• Three MINI-PCI Slots supports Type IIIA
  
• USB 2.0 Host
  
• Built in RS232/dB9 Connector
  
• SDIO
  
• On board Real Time Clock "RTC"
• DC Power Jack
  
• 802.3af 48V compatible

2. Power Supply Range 40VDC to 56VDC

• Using Higher voltage is recommended since it will use lower current
  
• Typical Power Consumption is 3W idle no radios present
  
• 5W idle One Radio present
  
• 7W while passing 1000Mbps traffic
  
• Single RJ45 "J1" is for WAN and 802.3af compatible Power Over Ethernet
  
• Supports high power POE up to 25W

3. Ethernet Interface

• J1 Single WAN port 10/100/1000
• J2 Tripple LAN Port 10/100/1000
• 2 RGMII Ethernet Logical Ports to Ethernet Phy Switch -
  • 1 RGMII port for WAN Port
  • 1 RGMII port for LAN Ports
• Ethernet Phy switch, Atheros AR8316

4. Real Time Clock "RTC" Interface

• RTC Interface shares the SPI bus with the on board FLASH
• Active high signal on SPI CS enables RTC, active low signal on SPI CS enables FLASH
• Manufacture Part# PCF2123TS Download Datasheet
  

5. Supported IO

UART J3 6 pin Header
Terminal Settings 115200 baud, 8 bits, nor parity, 1 stop bit.

Pin Out
Pin1	3.3VDC
Pin2	S_in
Pin3	NC
Pin4	NC
Pin5	S_out
Pin6	GND

JTAG Port "J4"
14 Pin header

Pin Out
Pin1	TRST	Pin2	GND
Pin3	TDI	Pin4	GND
Pin5	TDO	Pin6	GND
Pin7	TMS	Pin8	GND
Pin9	TCK	Pin10	GND
Pin11	RST	Pin12	NC
Pin13	NC	Pin14	3.3VDC

USER GPIO Header "J33"
Single Row 7 Pin Header Also next to it J5 dual row header to enable pull-up or pull-down for each GPIO user selectable in case User needs Active Low or Active High GPIO

J33 Pin out and Strapping option "place shunt to enable strapping option"

Pin Out	NAME	J5 STRAPPING
Pin1	GPIO_0	PULL LOW
Pin2	GPIO_1	PULL LOW
Pin3	GPIO_3	PULL LOW
Pin4	GPIO_4	PULL LOW
Pin5	GPIO_5	PULL HIGH
Pin6	GPIO_6	PULL HIGH
Pin7	GPIO_7	PULL HIGH

5. RESET BUTTON "SW4"

Uses GPIO_8 with weak pull-up, Active Low, for Resting back to factory defaults or multiple functions software dependent.

6. LED INDICATORS

Link/Act signals are connected to the Ethernet Phy Switch

LED	NAME	FUNCTION	GPIO
D29	POWER	3.3VDC	NA
D24	RF	RADIO Act	GPIO_2
DS4	WAN	Link/Act	NA
DS14	LAN1	Link/Act	NA
DS12	LAN2	Bold textLink/Act	NA
DS13	LAN3	Link/Act	NA

RouterStation Pro Software Specs

RouterStation Pro ships with OpenWRT Kamikaze. Ubiquiti only provides limited support for the software, but full support for the hardware.

All documentation for the use of OpenWRT can be found at the following website:

http://downloads.openwrt.org/kamikaze/docs/openwrt.html

Please look forward to a quick setup guide for a single radio setup.

No battery support for hardware